the one that still works
I tighten both screws. With an impact driver. And a dab of LocTite for good measure.
Well that’s retro but I used to only screw in the side that’s easier to reach because that already secures it while also allowing you to more easily unplug it again.
Lightly screw in one
And then replace my old shit and not touch anything but HDMI or DP for the last ten years.
Okay I’ll bite the bait. THE TOP ONE‽‽‽ What sick form factor are you using with vertical VGA ports?
You need to rotate your pc case if the VGA port isn’t vertical. The ground pins always need to be on top so all those grounding electrons weigh down the other conductors to make the data flow more quickly.
That’s not true. VGA is a horizontal spec with the entire trapezoid housing being the ground contact. The data electrons to one side is due to the earth’s axial tilt spinning them into a corner via healing crystals.
That’s when you use the ports placed on the motherboard in a standard verical PC case, meaning the system uses integrated graphics for the visual output instead of deticated videocard. Videocards that are put into MB at 90° are horizontal, right, but in most office setups I handle they are rare nowadays. Videocards are almost exclusively installed when you handle 3d and content rendering in demanding apps, and for office and browser stuff they are too costy after the crypto price hike and in a sanctioned Russia.
Nettops have horizontal motherboards tho.
standard verical PC case
Excuse you! Standard PC cases are horizontal:
Desktop computers that have a vertically standing motherboard.
Haven’t plugged in a VGA cable in a long time. As someone else pointed out it depends if it is temporary or long term… I always screw them in if it is long term
Haven’t plugged in a VGA cable in a long time.
Exactly. What have you done to HDMI and DP ports?
DVI is the Gen X of video connectors
VGA is the Boomers and HDMI is the Millenials. Gen-Z is using USB-C.
Nobody likes DisplayPort
DisplayPort is the cool uncle who is happy to mind the kids for free. A lot of people copy his smooth relaxed style and mannerisms without realising.
The cables are extra long so they have plenty of slack, too.
I just use HDMI or DP
DP
BBC?
Hand tight, then torque wrench, 7-inch pounds.
Pro tip: It’s a lot easier f you twist both knobs at the same time using the same motion as opening a bottle cap.
A school computer lab with a bunch of grubby-handed students touching and licking and who knows what to every surface? Yes, VGA cables get screwed down.
Jesus Christ, both!! 😆 But only finger tight. Sod you bastards who get the screwdrivers out! That’s overkill. 😁
When I used them, I screwed both in usually.
Who does just one? That’s worse than not doing either. Since they’re captive screws, doing just one can force the connector to wedge in crooked. I’ve had issues with tightening one too far before starting the threads on the other. Sometimes you have to go back and forth a couple times
After you properly connected it, sealing just one seems okay, isn’t it?
If you tighten just one side, it can pull the connector in that direction. Think of tightening heatsink screws unevenly on each side.
These seem way more forgiving tho. Up to the point you can connect it hot and working and it’d go nice.
It depends.
For my work computer, I screw them in tight, both on the monitor and the DP/VGA adapter.
For stationary devices (like overhead projectors) and extension cords, I screw them in, but not very tight.
For classroom computers, I only screw them in on the monitor and leave them unscrewed on the computer. Students can’t keep their legs calm and often snag the cables. I prefer to let the connectors harmlessly disconnect instead of damaging the graphics card or motherboard.
Both, three rotations after the threads catch.
One or none bears the risk of the connector coming out crooked and bending the pins, causing a potential alignment issue on the next connection and bending them further.
